Mirabel Informatique | André Ink

Brother DR-730, Resetting drum (photoconductor)

Thu, 03 Oct 2019 10:23:02 +0000

Choose for which type of printer you want to perform the Drum reset.. For the Brother HL-L2395DW, MFC-L2350DW, MFC-L2750DW: For the Brother DCP-L2550DW, HL-L2390DW, MFC-L2710DW: | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Brother TN-760, reset Toner

Wed, 02 Oct 2019 11:15:10 +0000

Choose for which type of printer you want to perform the toner reset.. For the Brother HL-L2395DW, MFC-L2350DW, MFC-L2750DW: For the Brother DCP-L2550DW, HL-L2390DW, MFC-L2710DW: | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Brother TN-660, reset Toner

Wed, 02 Oct 2019 09:08:07 +0000

There are two procedures for resetting the TN-630 & TN-660, Choose for which type of printer you want to perform the toner reset.. For the Brother DCP/MFC Series Printers (DCP-L2520DW, DCP-L2540DW, MFC-L2680W, MFC-L2685DW, MFC-L2700DW, MFC-L2705DW, MFC-L2707DW): Press Menu. Press the Up or Down arrow key to display the General Setup option, and then press OK. Press the Up or Down arrow key to display the Replace Toner option, and then press OK. Press the Up or Down arrow key to display the Continue or Stop option, and then press OK. Press Stop/Exit. For the Brother HL Series Printers (HL-L2300D, HL-L2305W, HL-L2315DW, HL-L2320D, HL-L2340DW, HL-L2360DW, HL-L2380DW): Open front cover and leave it open. Turn off printer. Hold GO button while turning printer on. After 3 seconds of printer being back on, release both buttons. (If you have a readout “User Mode” will appear, if you have no readout don’t worry) Press Go button 9 times. WiFi LED (if you have one) will flash once. (If you have no readout, go to next step.) Press Go button 5 times. Close the cover. For the Brother MFC Laser Printers ( MFC-L2720DW, MFC-L2740DW): Open the front cover of your Brother MFC laser printer where you can access its toner cartridge. Press and hold the Hash (#) button for about 5 seconds to see the toner menu on the screen. (The # key will be blacked out. If you are unsure where it is located press fax to find then press clear to perform the reset from your menu) Select the toner you need to reset (For the TN630 choose STD for TN660 choose HC) Select YES to reset. Close the front cover. DONE. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Vous n'en croirez pas vos yeux

Wed, 19 Jun 2019 16:45:01 +0000

Être vous un calculateur? Ou du style à tomber dans le piège Je sens que mes compétiteurs ne vont vraiment pas m’aimer aujourd’hui…. De toute façon ils ne m’aiment déjà pas. Ce n’est pas grave, je ne cherche pas à être aimé, les personnes allumées m’aiment déjà suffisamment, car j’aime dire les vraies choses, je m’excuse pareil pour les autres. Aujourd’hui je veux vous parler d’une bête noire qui brime de plus en plus l’industrie des cartouches d’encre et SURTOUT les consommateurs. Sachant que 90% des personnes et/ou entreprises achètent, beaucoup d’opportunismes se sont lancés dans la vente des cartouches compatibles et recyclées avec comme stratégie le Marketing du prix. Saviez-vous qu’actuellement 75% de toutes les cartouches d’encre vendues sur le marché sont commandées en ligne et que 9 personnes sur 10 vont privilégier les cartouches affichant le prix le moins cher croyant qu’ils ont économisé et que seul le prix les différencie! Croyez-vous au père-Noël? On dirait que quand ça touche notre Portefeuille, le Père-Noël existe. Posez-vous la question! S’il existait, pourquoi beaucoup d’entreprises ont un département d’achat en contrôle de qualité? Je vais me permettre un petit écart sur le responsable du piège… Le Marketing du prix. Cette stratégie des prix est rendue tellement puissante que tous les gourous du marketing l’utilisent aisément. 2ième paire de lunettes gratuite, pizza 2 pour 1. Celui de la SAQ a été monté d’une main de maître. En 2015, la société d’état SAQ annonce une augmentation de prix pour, par la suite, sortir sa carte fidélité inspire qui vous donne une ristourne! Une carte fidélité, trop drôle… On ne peut pas acheter ailleurs nos spiritueux, SAQ a le monopole. Mais cela a fonctionné, 3.7 millions de cartes fidélité en circulation! La croissance des ventes de la SAQ a bondi avec une poussée de 129 millions en 3 mois. Vive le Marketing des prix. Revenons à nos cartouches … Je ne vais sûrement rien apprendre à personne, mais... fabriquer une cartouche d’encre compatible ou recyclé de qualité pour qu’elle offre le meilleur rapport qualité-prix pour le client coûte un minimum d’argent. Vous n’en croirez pas vos yeux. 85% des cartouches compatibles vendues sur le marché sont vendues moins chères que son prix de fabrication minimal. Ces cartouches soi-disant économiques pourraient endommager vos équipements, et que les consommateurs vont devoir en acheter 2 et même 3 fois plus pour arriver au rendement d’un produit de qualité. Non, mais! Quand tu construis des cartouches avec les composantes les plus cheaps disponibles et que l’important est que ça imprime pour pouvoir vendre un prix… ça vous intéresse? Souvenez-vous des 9 personnes sur 10! Êtes-vous surpris? Moi, non. Le monde aime croire au Père-Noël. Le pire, même si on leur prouve qu’ils vont tomber dans le piège des prix, ils vont continuer. Heureusement, ce n’est pas « difficile » de vraiment économiser, il y a vraiment de bonnes cartouches compatibles et recyclées sur le marché. Choisissez vos fournisseurs en fonction de leur réputation et surtout de leur expérience. Méfiez-vous de ceux qui vendent plein d’autres affaires sur leur site Web. Les vrais spécialistes se dévouent uniquement à ce qu’ils maîtrisent. Méfiez-vous des indications que contiennent les cartouches Nombre de pages / Page Yield … est en général le nombre de pages que la cartouche d’origine imprime. Date d’expiration. Une cartouche expirée, même les meilleures perdent de leur efficacité et rendement. Version. Les cartouches d’aujourd’hui contiennent des puces électroniques qui sont continuellement en évolution. Cette puce est la communication entre la cartouche et l’imprimante et parfois même avec le manufacturier du produit d’origine. Cette puce calcule le nombre de copies que vous allez imprimer avec votre cartouche en fonction de 5% de couverture. Elle détermine aussi le comportement de la cartouche, quantité d’encre à transférer, etc. Les imprimantes d’aujourd’hui se mettent à jour automatiquement, les puces doivent continuellement être mis à jour par le manufacturier. Génération et Encre : Est en général le type d’encre utilisée dans la cartouche. L’importance est… Si la cartouche d’origine est par exemple un laser de polyester 0.32 micron, la cartouche compatible doivent avoir le même type et le même micron. Pour les jets d’encre, on parle surtout de picolitres. Je tiens à remercier ma fidèle clientèle qui partage continuellement mes blogues. C’est formidable comme le bouche-à-oreille fonctionne, vous êtes ma meilleure équipe de vente.

Brother TN-221 / TN-225, Reset Toner

Tue, 29 Jan 2019 17:17:46 +0000

There are two procedures for resetting the TN-221 & TN-225, depending on whether you have a print-only device (HL series) or multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (séries MFC): MFC-9130CW et MFC-9340CDW If you have a Brother multifunction machine (MFC series) and you recently replaced your TN-221 & TN-225 toner cartridge, you can manually reset the remaining toner. - Make sure the printer is turned on - Press the Cancel / Delete (X) key to bring up the main menu until an error message appears on the LCD. - Press the keys to bring up the numeric keypad. - Tap the asterisk (star) on the numeric keypad. It is important to remember where you stand because the keyboard will not be illuminated later. - Press the home key to return to the main menu. - Lift the front cover of the printer to access the cartridges. - Once the lid is raised, press and hold the asterisk (star) key for about 5 seconds. - The reset menu will now appear on the LCD screen. K-TNR-221 Black (Standard yield) / (High yield) C-TNR-221 Cyan (Standard yield) / C-TNR-225 Cyan (High yield) Y-TNR-221 Yellow (Standard yield) / Y-TNR-225 Yellow (High yield) M-TNR-221 Magenta (Standard yield) / M-TNR-225 Magenta (High yield) - LCD will display "accepted" after reset completed - Close the lid. Multi-function Device (séries MFC): MFC-9130CW et MFC-9340CDW If you have a Brother multifunction machine (MFC series) and you recently replaced your TN-221 & TN-225 toner cartridge, you can manually reset the remaining toner. - Make sure the printer is turned on - Open the printer cover to see the toner cartridges - Press and hold the asterisk (*) key for five (5) seconds (keeping the lid open) - The LCD screen should display a new menu. - Browse through the menu to select the color and output. K-TNR-221 Black (Standard yield) / (Haut rendement) C-TNR-221 Cyan (Standard yield) / C-TNR-225 Cyan (High yield) Y-TNR-221 Yellow (Standard yield) / Y-TNR-225 Yellow (High yield) M-TNR-221 Magenta (Standard yield) / M-TNR-225 Magenta (High yield) - Reset? Appear on the screen Select "Yes". - Close the printer cover. Alternative: If the asterisk (*) key does not work, try the pound / number sign instead Print device only (HL series) - With the lid up, press the "Secure" and "Cancel / Stop" buttons at the same time - The LCD will display reset - Browse through the menu to select the color and output to reset K-TNR-221 Black (Standard yield) / (High yield) C-TNR-221 Cyan (Standard yield) / C-TNR-225 Cyan (High yield) Y-TNR-221 Yellow (Standard yield) / Y-TNR-225 Yellow (High yield) M-TNR-221 Magenta (Standard yield) / M-TNR-225 Magenta (High yield) - LCD will display "accepted" after reset completed Close the lid. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Brother TN-339, reset Toner

Fri, 21 Dec 2018 12:59:00 +0000

There are two procedures for resetting the TN-331 & TN-336 depending on whether you have a print device only (HL series) or a multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (MFC series): If you have a Brother MFP (MFC Series) and have recently replaced your TN-331 & TN-336 Toner Cartridge, you can manually reset the remaining toner. Open the front cover. Hold 5 seconds the “down arrow”, if the pad is not visible, simply touch the pad to activate Press the up or down arrow buttons to select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow (Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Once you have selected your cartridge, press “yes” to reset the selected toner cartridge. Repeat for each toner cartridges color as required. Close the front cover. Print device only (HL series): If you have a Brother machine (HL Series) and have recently replaced your TN-331 & TN-336 Toner Cartridge, you can manually reset the remaining tonert. Open the front cover. Press the “Secure” and “Cancel” buttons at the same time“. Reset Menu opens, with the Down Arrow, locate the cartridge to reset. Select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow(Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Press the "Yes" button to reset the selected toner cartridge. Repeat for each color of toner cartridge if necessary. Close the front cover. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Brother TN-331 & TN-336, reset Toner

Fri, 21 Dec 2018 08:05:01 +0000

There are two procedures for resetting the TN-331 & TN-336 depending on whether you have a print device only (HL series) or a multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (MFC series): If you have a Brother MFP (MFC Series) and have recently replaced your TN-331 & TN-336 Toner Cartridge, you can manually reset the remaining toner. Open the front cover. Press the "clear / return" button. (If the display shows "Please Wait", open the front cover and "Cover Open" * Press the "1" button.) Reset Menu” appears on the LCD display. Press the up or down arrow buttons to select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow (Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Push the button “Ok”. Close the front cover. Print device only (HL series): If you have a Brother machine (HL Series) and have recently replaced your TN-331 & TN-336 Toner Cartridge, you can manually reset the remaining tonert. Open the front cover. Press the “Secure” and “Cancel” buttons at the same time“. Reset Menu” appears on the LCD display. Press the up or down arrow buttons to select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow(Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Push the button “Ok”. Press the up or down arrow button to select the toner cartridge that needs to be reset. Close the front cover. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

TN560 & DR500 Laser Repetitive Table

Thu, 20 Dec 2018 17:05:10 +0000

Horizontal problem Drum (Photoconductor): 94.1mm Magnetic/ Developer Roller : 39mm Upper fuser roller: 78.5mm lower fuser roller: 78.5mm Vertical trails problem Problem too pale impressions This problem usually appears when your cartridge is at the end of its life (empty). The Brother technology for the page counter is mechanical and therefore inaccurate. It happens regularly that a cartridge can be empty without the printer indicates it.

TN460 & DR400 Laser Repetitive Table

Thu, 20 Dec 2018 16:27:44 +0000

Brother TN-310 & TN-315, reset Toner

Thu, 20 Dec 2018 10:28:21 +0000

There are two procedures for resetting the TN-310 & TN-315 depending on whether you have a print device only (HL series) or a multifunction device (DCP / MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother DCP / MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (DCP/MFC series): If you have a Brother MFP (DCP / MFC Series) and have recently replaced your TN-310 & TN-315 Toner Cartridge, you can manually reset the remaining toner. Open the front cover. Press the "clear / return" button. (If the display shows "Please Wait", open the front cover and "Cover Open" * Press the "1" button.) Reset Menu” appears on the LCD display. Press the up or down arrow buttons to select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow (Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Push the button “Ok”. Push the button Stop / Exit. Close the front cover. Print device only (HL series): If you have a Brother machine (HL Series) and have recently replaced your TN-310 & TN-315 Toner Cartridge, you can manually reset the remaining tonert. Open the front cover. Press the “Secure” and “Cancel” buttons at the same time“. Reset Menu” appears on the LCD display. Press the up or down arrow buttons to select the cartridge you want to reset. K-TNR-STD Black (Standard yield) / K-TNR-HC Black (High yield) C-TNR-STD Cyan (Standard yield) / C-TNR-HC Cyan(High yield) Y-TNR-STD Yellow(Standard yield) / Y-TNR-HC Yellow (High yield) M-TNR-STD Magenta (Standard yield) / M-TNR-HC Magenta (High yield) Push the button “Ok”. Press the up or down arrow button to select the toner cartridge that needs to be reset. Press the Stop / Exit button. Close the front cover. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

TN-450 & DR-4200 Laser Repetitive Table

Thu, 20 Dec 2018 07:59:24 +0000

Horizontal problem Drum (Photoconductor): 94.2mm Magnetic/ Developer Roller : 32.5mm Upper fuser roller: 53.4mm lower fuser roller: 78.5mm Vertical trails problem Problem too pale impressions This problem usually appears when your cartridge is at the end of its life (empty). The Brother technology for the page counter is mechanical and therefore inaccurate. It happens regularly that a cartridge can be empty without the printer indicates it.

Brother TN-210, reset Toner

Wed, 19 Dec 2018 14:30:16 +0000

There are two procedures for resetting the TN-210, depending on whether you have a print-only device (HL series) or multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Read comments | Leave your comment | Multi-function Device (MFC & HL series): If you have a Brother multi-function (MFC/ HL series) machine and recently replaced your TN-210 toner cartridge, you can manually reset the toner remaining Open the front cover . Press “clear/back button”. You will see “K-TNR-STD” display on the screen’. Using the “+” and “-” buttons select the toner you want to reset. Press the up or down arrow button to select the toner cartridge that needs to be reset. - K-TNR-STD Noir - C-TNR-STD Cyan - Y-TNR-STD Jaune M-TNR-STD Magenta After selecting the appropriate toner cartridge press OK”. ("Ok?" Will be displayed) Click the "Ok" button again to reset the toner. Close the lid. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

TN-360 & DR-360 Laser Repetitive Table

Tue, 18 Dec 2018 16:10:02 +0000

Horizontal problem Drum (Photoconductor): 75mm Magnetic/ Developer Roller : 41mm Upper fuser roller: 78.5mm lower fuser roller: 78.5mm Vertical trails problem Problem too pale impressions This problem usually appears when your cartridge is at the end of its life (empty). The Brother technology for the page counter is mechanical and therefore inaccurate. It happens regularly that a cartridge can be empty without the printer indicates it.

Brother TN-450, reset Toner

Tue, 18 Dec 2018 14:41:44 +0000

There are two procedures for resetting the TN-420 & TN-450, depending on whether you have a print-only device (HL series) or multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother DCP & MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (DCP/MFC series): If you have a Brother multi-function (DCP/MFC series) machine and recently replaced your TN-420 & TN-450 toner cartridge, you can manually reset the toner remaining Open the front cover. Press the ‘back’ button. Press *00. (Ignore drum message). It should say accepted on the display screen. Close the door. Print-only Device (HL series): If you have a Brother multi-function (HL series) machine and recently replaced your TN-420 & TN-450 toner cartridge, you can manually reset the toner remaining. Open the Front cover. Turn off printer Press and hold the GO button. Power ON the printer while continuing to hold the GO button. Once the 3 LED’s are lit, release the GO button. Press the GO button 2 times. This will cause the LED’s to light solid. With the LED’s lit solid, press the GO button 5 times. Toner will be reset. Close the front cover. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Brother DR-420, Resetting drum (photoconductor)

Tue, 18 Dec 2018 14:07:20 +0000

Brother TN-360, reset Toner

Mon, 17 Dec 2018 16:57:21 +0000

There are two procedures for resetting the TN-330 and the TN-360, depending on whether you have a print-only device (HL series) or multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother DCP | Brother HL | Brother MFC | | Read comments | Leave your comment | Multi-function Device (DCP series): If you have a Brother multi-function (DCP/MFC series) machine and recently replaced your TN-330 & TN-360 toner cartridge, you can manually reset the toner remaining Open the front toner compartment door. The printer screen should read “front cover is open”. Press the “clear” button on the printer’s front panel. Printer will say “Replace Drum?” Here do not press 1 but instead type in “*00” on the keypad. Star zero zero. The screen will say “Accepted”. Close the front cover and the low toner message will be reset. Print-only Device (HL series): If you have a Brother multi-function (HL series) machine and recently replaced your TN-330 & TN-360 toner cartridge, you can manually reset the toner remaining. Open front door. Turn off printer. While holding down the GO button, turn printer back on. When all four LEDs light up release GO button. All LEDs will turn off. Press the GO button 2 times. The 3 LEDs (toner, drum, paper) will light up solid. Press the GO button 5 times. Paper light will be blinking. At this point the toner end-of-life condition has been reset. Close front door. Multi-function Device (MFC series): If you have a Brother multi-function (MFC series) machine and recently replaced your TN-330 & TN-360 toner cartridge, you can manually reset the toner remaining Open the front toner compartment door. The printer screen should read “front cover is open”. Press the “clear” button on the printer’s front panel. Printer will say “Replace Drum?” Here do not press 1 but instead type in “*00” on the keypad. Star zero zero. The screen will say “Accepted”. Close the door and it will reset the low toner message. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

TN-350 & Dr-350 Laser Repetitive Table

Mon, 17 Dec 2018 10:00:47 +0000

Brother TN-350, reset Toner

Sun, 16 Dec 2018 13:33:42 +0000

There are two procedures for resetting the TN-350, depending on whether you have a print-only device (HL series) or multifunction device (MFC series). Choose for which type of printer you want to perform the drum reset.. | Brother DCP & MFC | Brother HL | | Read comments | Leave your comment | Multi-function Device (DCP/MFC series): If you have a Brother multi-function (DCP/MFC series) machine and recently replaced your TN-350 toner cartridge, you can manually reset the toner remaining Open the front cover. Press the ‘back’ button. Press *00. (Ignore drum message). It should say accepted on the display screen. Close the door. Print-only Device (HL series): If you have a Brother multi-function (HL series) machine and recently replaced your TN-350 toner cartridge, you can manually reset the toner remaining. Open the Front cover. Turn off printer. Press and hold the GO button. Power ON the printer while continuing to hold the GO button. Once the 3 LED’s are lit, release the GO button. Press the GO button 2 times. This will cause the LED’s to light solid. With the LED’s lit solid, press the GO button 5 times. Toner will be reset. Close the front cover. | Read comments | Leave your comment | Source of information: Service support, Brother & SCC & Uninet & Summit

Reset drum (photoconductor) IBM & Lexmark

Sun, 16 Dec 2018 11:45:40 +0000

How to reset the photoconductor counter | Read comments | Leave your comment | Overview A Photoconductor (PC) Life Warning or a Replace Photoconductor message on the printer screen indicates that the photoconductor unit in the printer is near or past its expected life rating of 30,000 single-sided pages. You will need to replace the photoconductor unit inside the printer when you see this message. NOTE: It may occasionally be necessary to replace the photoconductor unit in order to correct a print quality problem such as toner streaks on the page. Replacing the photoconductor unit/kit WARNING! When replacing a photoconductor kit, do not leave the new photoconductor kit exposed to direct light (especially sunlight) for an extended period of time. Extended light exposure can cause damage to the new photoconductor kit, which may lead to print quality problems. Step Action Click Image to Enlarge 1 Press the button on the left-hand side of the printer and open the front door. 2 Remove the print cartridge assembly. Grasp the toner cartridge handle and pull up and out. Note: Do not press the button on the print cartridge assembly. Place the print cartridge assembly on a flat, clean surface. 3 Separate the toner cartridge from the photoconductor unit. Press the button on the base of the print cartridge assembly. Grasp the toner cartridge handle, and pull up and out. 4 Unpack the new photoconductor kit. 5 Install the toner cartridge into the new photoconductor unit. Align the white rollers on the toner cartridge with the white arrows on the tracks of the photoconductor. Push the toner cartridge in as far as it will go. It should click into place when correctly installed. 6 Install the print cartridge assembly into the printer. Align the green arrows on the guides of the print cartridge assembly with the green arrows on the tracks in the printer. Push the print cartridge assembly in as far as it will go. 7 Close the front door. 8 Reset the photoconductor counter. 1. Install the new kit(or used kit) with the printer is turned ON. 2. Open the front panel. 3. Hold the Cancel button in until the front panel LEDs flash. 4. Close the front panel and ready to use!!!! | Read comments | Leave your comment | Source of information: Service support, IBM & Lexmark & SCC & Uninet & Summit

Reset drum (photoconductor) Dell

Sat, 15 Dec 2018 10:38:47 +0000

How to reset the photoconductor counter | Read comments | Leave your comment | Instructions Resetting the Drum Page Counter 1 Shut off the printer. 2 Hold down the "Cancel" button while opening the front door. Then turn on the printer 3 Keep the Continue button held down until only the "Error LED" is on then release the button. Close the door. 4 The Continue button, Ready/Data, Toner Low, and Load Paper LEDs should all be lit up. 5 Press "Cancel" a few times to cycle through the LEDs until just the "Toner Low LED" is lit. 6 Press and hold the "Continue" button until the LEDs cycle through and release only when the LED stops at Toner Low. 7 Turn the printer off and back on. | Read comments | Leave your comment | Source of information: Service support, Dell & SCC & Uninet & Summit